Skip to Content

Runtech holds the quality of every packaging machine to four checkpoints. On certification, the company is certified to ISO 9001:2015, ISO 45001:2018 and ISO 14001:2015, and provides an individual CE certificate for each single machine, owned by the customer. 

Packaging Machine Quality Control & CE Compliance | Runtech

Packaging Machine Manufacturer · Changzhou, China

Quality Control: The Four Checkpoints We Hold


Checkpoint 1 — Incoming Inspection

Components, contact parts and electrical items are checked against the purchase specification before release — no material goes straight from the delivery note to the assembly bench. The point is not to catch everything at the door, but to make problems visible and owned.

  • Contact parts are checked for material identification, using SUS304 or 316L stainless where the product and industry require it
  • Surfaces are checked for cuts, deformation or residue that would be difficult to clean out later
  • Electrical items are checked for correct type and rating against the machine's electrical design
  • Non-conforming items are segregated and marked so they cannot enter a build

Checkpoint 2 — In-Process Inspection

On the assembly floor, inspectors work to defined checkpoints rather than a vague "look it over." The goal is to catch a drift in alignment or a loose connection while the machine is still open and easy to correct — not after it is wrapped for freight.

  • Mechanical alignment at guide rails, starwheels and transfer points
  • Wiring checked against the schematic before the cabinet closes
  • Pneumatic tubing and servo integration: routing, connections and response

Checkpoint 3 — Factory Acceptance Testing (FAT)

Every machine goes through a 100% FAT, including a 24-hour continuous run — sustained operation, not a demonstration with the cover off. The test uses sample bottles and liquid (or an equivalent test fluid) and produces a record that travels with the machine.

  • Leak checks at the filling and capping stations
  • Filling accuracy ±0.5%; capping pass rate 99.8%
  • Smooth operation of drives, guide rails and transfer points
  • Behaviour under continuous running

The FAT covers machine function and stability under test conditions only; it does not validate your recipe, shelf life or regulatory filing. The process applies across the machines we build, from single units to integrated lines, including our filling machines.


Checkpoint 4 — Inspection Records and Traceability

Every machine has the same inspection record structure; a record that only says "checked, OK" does not pass. A finished machine can be traced from its serial number back to its major components — turning "we think it's this valve" into "the valve fitted at serial number X is this one."

Record fieldWhat gets recorded
Machine / dateAsset ID, shift and inspection date.
Inspection pointCapping head, chuck, gripper, clamp, guide rail, bearing, transmission, sensor or other confirmed point.
Condition / evidenceFactual observation plus measurement, photograph or comparison reference where available.
Action / spareCleaned, adjusted, replaced, escalated or no action; include confirmed spare-part reference when used.
Next requirementManual-defined interval, approved follow-up or further machine-specific inspection.

Certificates and Compliance


The company holds ISO 9001:2015, ISO 45001:2018 and ISO 14001:2015 management system certifications. For CE, an individual certificate is available for each single machine and can be arranged to the customer's requirements. Certificate ownership belongs to the customer — we do not retain copies. Certificate numbers, issuing bodies and years are subject to the certificate actually delivered to you, so we do not list them here.

Certification / ComplianceStandard or descriptionWhat it means for you
Quality management systemISO 9001:2015From incoming parts to shipment, the process is documented and records are available for audit.
Occupational health and safety management systemISO 45001:2018Assembly and testing are carried out in a controlled, safe environment.
Environmental management systemISO 14001:2015Production and resource use are managed to environmental requirements.
CE compliance and single-machine certificateDeclaration of Conformity and technical documentation; an individual certificate is available for each machine, arranged to customer requirementsOwnership belongs to the customer — we do not retain copies — giving clear title for your compliance filing and audits.


CE documents a serious buyer should request:

  • Declaration of Conformity
  • Electrical schematics
  • Risk assessment
  • Material identification for contact parts
  • Operating manual in the destination language
  • Nameplate and serial data

CE does not certify output, yield or filling accuracy — it does not mean the machine will hit a given bottles-per-minute figure in your plant.

Send us a message

To prepare your questions, browse more technical guides; or contact us with your bottle, cap and destination market, and we will put the records we can show you in front of you.